（13） Metal Jacketed Gasket to JPI(ANSI/ASME) raised face flange（table 1.1.27)

Products （VALQUA No.）	Product Dimension Standard	Applicable Flange Standard
●Non-Asbestos N520、N6520、N510、N6510 (Incl Metal Jacketed gasket with handle)	VALQUA Standard	JPI-7S-15 ANSI/ASME B16.5

Table 1．1．27　Unit mm

Nominal Dia		Standard Type Metal Jacketed			Metal Jacketed Gasket with Handle
A	B	ID D1	OD D2		Gasket			Handle
					ID D1	OD D2		Length D3		Center Circle Dia C		Bolt Hole Dia h		Width W
			Class 150	Class 300		Class 150	Class 300	Class 150	Class 300	Class 150	Class 300	Class 150	Class 300	Class 150	Class 300
15	½	25	47	53	25	35	35	89	95	60.5	66.5	16	16	26	26
20	¾	33	56	66	33	43	43	98	117	70	82.5	16	20	26	30
25	1	38	66	72	38	51	51	108	124	79.5	89	16	20	26	30
(32)	1¼	48	75	82	48	64	64	117	133	89	98.5	16	20	26	30
40	1½	54	85	94	54	73	73	127	156	98.5	114.5	16	23	26	33
50	2	73	104	110	73	92	92	152	165	120.5	127	20	20	30	30
65	2½	86	123	129	86	105	105	178	191	139.5	149	20	23	30	33
80	3	108	135	148	108	127	127	191	210	152.5	168	20	23	30	33
(90)	(3½)	121	161	164	-	-	-	-	-	-	-	-	-	-	-
100	4	132	173	180	132	157	157	229	254	190.5	200	20	23	30	33
(125)	(5)	160	196	215	160	186	186	254	279	216	235	23	23	33	33
150	6	190	221	250	190	216	216	279	318	241.5	270	23	23	33	33
200	8	238	277	306	238	270	270	343	381	298.5	330	23	26	33	36
250	10	286	338	360	286	324	324	406	445	362	387.5	26	29	36	44
300	12	343	408	420	343	381	381	483	520	432	451	26	32	36	47
350	14	375	449	484	375	413	413	535	585	476	514.5	29	32	44	47
400	16	425	512	538	425	470	470	595	650	539.5	571.5	29	35	44	50
450	18	489	547	595	489	533	533	635	710	578	628.5	32	35	47	50
500	20	533	604	651	533	584	584	700	775	635	686	32	35	47	50
600	24	641	715	772	641	692	692	815	915	749.5	813	35	42	50	62

【Note】
1. Standard thickness of Metal Jacketed Gasket is 3mm but other thickness are available.
2. 0.4mm T VALQUAFOIL（Expanded Graphite Tape）can be laminated to both sides of Metal Jacketed gaskets （VFMetal Jacketed ）.
3. Standard thickness of hadle is 0.4mm.
4. Standard material of handle is SPCC. Please specify if the same material as Gaske part is requested for handle.
５．Please do not use Nominal Dia products in parentheses as much as possible.